≡ Param Finder by package / current / voltage
MF-R110 插件 插件自恢复保险丝
上一张
  • MF-R110 插件 插件自恢复保险丝
下一张

Bourns MF-R110 Resettable Fuse 1.10A 30V Radial Leaded

Bourns MF-R110 radial leaded resettable fuse, 1.10 A hold current, 30 V maximum voltage, 插件 package. Self-resetting after the fault is cleared, no replacement needed.

Download

0

The MF-R110 is a radial-leaded through-hole resettable fuse that carries 1.10 A continuously and withstands 30 V maximum. Its body is 8.9 mm maximum in diameter, the leads sit 5.1 mm apart on a 0.51 mm diameter, and it solders through the board. cUL and TÜV recognised, epoxy body to UL 94V-0. Commonly used for overcurrent protection on power boards, industrial control boards and equipment that is serviced in the field.

Brand:BOURNS (Joincircuit is an authorised distributor)
Category:Resettable fuse / Through-hole, DIP radial leaded (through-hole)
Voltage:30 V; Current:hold 1.1 A; trip 2.2 A.

Specifications

ParameterValue
Hold current1.1 A
Trip current2.2 A
Maximum voltage30 V
Maximum fault current40 A
Initial resistance0.1 Ω
Post-trip max resistance0.27 Ω
Trip current / time5.5 A / 6.6 s
Dissipated power0.7 W
PackageDIP radial leaded (through-hole)

Temperature Derating

-40℃-20℃0℃23℃40℃50℃60℃70℃85℃
Hold current (A)1.61.431.271.10.910.850.750.670.57
Share of 23 °C rating145%130%115%100%83%77%68%61%52%

Product Description

What this product is

The MF-R110 is a polymer resettable fuse placed in series between a supply and its load to limit current. Above 2.20 A the internal material expands with heat, resistance climbs and the loop current is held to a low value. Once the fault is cleared and the part cools, it conducts again by itself. The leads pass through the board and solder into holes, so a failed part comes out with a soldering iron.

Dimensions and appearance

Radial leads, body 8.9 mm maximum diameter, 14.0 mm from the top of the body to the kinked section, 5.1 mm between lead centres, 0.51 mm lead diameter in tin-plated copper. The kinked leads hold the body off the board, so its heat does not pass straight into the PCB. Marked R110 with the production lot. Supplied 500 pcs per bag, or on tape.

How it works

It sits in series in the loop. At 23 ℃ and 1.10 A its own resistance is 0.10 Ω, which gives a drop of 0.11 V. Above 2.20 A, or as ambient temperature rises, the internal material expands with heat, resistance climbs and the current is limited. At a fault current of 5.5 A it opens within 6.6 s.

After the fault is cleared

When the part cools after a trip, resistance falls back to the low state and the loop runs again with no manual reset. After one trip the resistance is at most 0.27 Ω, 2.7 times the 0.10 Ω factory value, which gives 0.30 V at 1.10 A.

Parameters and selection

The full datasheet is available for download on this page, covering the derating table and time-current curves. At 60 ℃ inside an enclosure the hold current is 0.75 A, and 0.57 A at 85 ℃. On a 24 V rail a charged battery reaches 28.8 V, which leaves 1.2 V below the 30 V ceiling. For lot confirmation, stock, or a 60 V part in the same current class, contact our sales team.

Selection Notes

1. It comes back out with a soldering iron

The leads pass through the board and solder into holes, so a failed part lifts out with an iron and a solder sucker and one board is saved. A surface-mount part needs hot air, which heats body and pads together and works the pads every time it is removed. Where the board stays in service, changing one part beats scrapping it. It also sheds heat better: the 0.70 W it dissipates when tripped leaves from a body standing clear of the board, so the joints and copper take less of it.

2. 60 V means dropping to 0.90 A

This is the only 1.10 A part in the series and it is rated 30 V. Going to 60 V means dropping to the MF-R090 at 0.90 A; every model above 1.10 A is 30 V as well. Where a 24 V rail needs wide margin, the load has to fit inside 0.90 A, so confirm that first and then pick the part.

3. 6.6 s is what a 5.5 A fault gets

The datasheet time to trip is 6.6 s at 5.5 A. The 0805 part at the same 1.10 A opens in 0.30 s at 8 A, because the larger through-hole body takes longer to reach trip temperature. Between 2.20 A and 5.5 A the time is longer still, so read the time-current curve instead of assuming 6.6 s.

Up Page:Is the first!

Next Page:Bourns MF-R Series Radial Leaded Resettable Fuses