How does an automotive fuse protect a circuit, and what effect do automotive fuses have on a vehicle? In everyday life we often meet this question: a fuse no bigger than a fingertip can protect the safety of an entire vehicle system, and curiosity about how that protection works is something every car enthusiast would like satisfied. Today we will look at how an automotive fuse protects a circuit.
An automotive fuse is a type of electrical fuse. When the circuit current exceeds twice the rated current of the fuse, the fuse element melts within a few seconds and protects the circuit. Automotive fuses are widely used for overcurrent protection in vehicle circuits and also for overcurrent protection in industrial equipment. An automotive circuit is a closed loop formed by conductors (wires) linking three things: the power source (the battery), the control devices (switches, relays and so on) and the loads (lamps, motors and so on).
Take a headlamp circuit as an example. In normal operation the current runs from the positive terminal of the battery to the lamp switch and then to the negative terminal. The battery negative is bonded to the steel body or frame of the car, so the headlamp negative does not normally have to be run back to the battery; it is connected to the nearest point on the body or frame instead. We call this body grounding, and its principle is simply a connection to the battery negative. (Related reading: Protection of Automotive Central Locking Motors with Resettable Fuses)
Of course, the circuit described above is a simple one; on many vehicles the headlamp circuit is more complicated. The gauge of the headlamp conductor (usually also called the wire), that is, how thick the wire is, has to be chosen according to the rated current of the headlamp. A wire that is too thin heats up and causes an excessive voltage drop, so the headlamp does not receive its rated voltage and its light output falls; a wire that is too thick wastes copper.
The rule for choosing a wire is therefore simple: it should not heat up in normal operation, and the voltage drop should stay within the permitted range.
In a circuit every powered device is a burden on the supply, which is why it is called a load; the headlamp is the load on the battery. If the headlamp is rated 60 W and you fit a 100 W bulb, the operating current will be far higher than before. Motor loads behave the same way: a wiper motor may be jammed by a foreign object so that it can no longer turn. All of these faults raise the operating current by a factor of three or more.
Automotive fuse
An operating current above the rated current of the original load is called an overload. A small overload, such as replacing a 60 W bulb with a 100 W one, can be absorbed by leaving a little safety margin in the choice of wire, and the wire will not overheat. At connectors, however, contact resistance is higher and heating is greater, so the headlamp socket is often burned out; this can easily produce a much larger overload multiple, and over time the motor and the wiring are destroyed by severe heating. (Related information: Resettable Fuses in Automotive USB Systems)
Against this background the role of the fuse becomes obvious. A fuse is made of a low-melting-point alloy, and when an overload current passes through it the element melts before the motor and the wiring overheat, cutting off the circuit; that is how it protects them.
That is the theory, but in practice a fuse gives only simple circuit protection and does not protect a motor particularly well. It often happens that a power wire is connected to a ground wire, so that current flows from the battery positive straight back to the battery negative. That readily creates a short circuit: the current taking this shortcut is called a short-circuit current and can reach tens of times the normal value. If such a current is not interrupted at once, the wire soon overheats, smokes and its insulation melts; if the short-circuit current is large enough to raise the conductor temperature to the ignition point of the insulation, open flame follows. Many vehicle fires start exactly this way.
Because the circuit contains a fuse, the fuse opens immediately (within 5 seconds) once the short-circuit current passes and cuts off the circuit. No current flows, so self-ignition cannot occur. In other words, with a fuse fitted a short circuit has no serious consequences; without one, a short circuit will at best burn out the wiring and at worst set the car on fire. (Recommended reading: Automotive Fuses: What You Need to Know)
The importance of the fuse should now be self-evident. One point deserves special emphasis: when you replace an automotive fuse, always use the same rating as the original. Never fit a fuse with a higher current rating, and never replace it with another conductive object. Many auto parts shops sell counterfeit or substandard fuses, so if you are unsure of the source, have the fuse changed at a 4S dealership, and even there ask whether the part is “genuine”.