深圳市集电通实业有限公司

电话 : 0755-8830-8258

邮编 : 518129

邮箱 : andyzheng@jdtfuse.com

网址 : http://www.joincircuit.com/

How to Tell Fast-Acting from Time-Lag Fuses

In an earlier article we explained: Differences Between Fast-Acting and Time-Lag Fuses, which gave you a deeper understanding of fast-acting and time-lag behaviour. How, then, do you tell a fast-acting fuse from a time-lag one? This article gives a brief explanation.
 
 
How to tell a fast-acting fuse from a time-lag fuse—a time-lag fuse is also called a delay fuse. Its time-delay characteristic means that it stays intact when a non-fault pulse current appears in the circuit, while still protecting against long-term overload. In some circuits the current at the instant of switching is several times the normal operating current. Although the peak value of this current is high, it lasts only a very short time; it is called a pulse current, an impulse current or a surge current.
 
 
An ordinary fuse cannot withstand such a current. In such a circuit an ordinary fuse may prevent the equipment from starting at all, while a fuse of a larger rating gives no protection when the circuit is overloaded. The fuse element of a time-lag fuse is specially processed so that it can absorb energy; by adjusting the amount of energy absorbed, the fuse can both withstand inrush currents and provide overload protection. Standards specify the time-delay characteristics; if the characteristics required by the standard do not meet your needs, please contact the manufacturer for a solution.
 
 
How to tell a fast-acting fuse from a time-lag fuse—the main difference between a time-lag fuse and a fast-acting fuse is its ability to withstand transient pulse currents. In other words, it withstands the surge current that occurs at power-on and power-off without operating, so the equipment keeps working normally. A time-lag fuse is therefore often called a surge-resistant fuse.
 
 
Technically, a time-lag fuse has a larger melting heat value, so more energy is needed to melt it. For fuses of the same rated current, a time-lag fuse therefore withstands pulses far better than a fast-acting one. Because its heat value is larger than that of a fast-acting fuse of the same rating, it also takes longer to open when an overcurrent occurs in the circuit. (Further reading: Can I Request Free Samples on the Website?)
 
 
Once a fault occurs in the circuit, the overcurrent will not disappear by itself, and the energy of a sustained overcurrent greatly exceeds the heat value of the fuse, so any fuse will open. The difference in opening time between a time-lag fuse and a fast-acting fuse is not very important for protection requirements; only when sensitive components in the protected circuit need protection does a time-lag fuse have any effect on protection performance.
 
 
How to tell a fast-acting fuse from a time-lag fuse—because of these differences, time-lag and fast-acting fuses are used in different circuits. A fast-acting fuse must be used in a purely resistive circuit (no surge or very little) or in a circuit that protects sensitive, expensive components such as ICs. A time-lag fuse is the better choice for capacitive or inductive circuits (which have a surge at power-on and power-off) and for the input and output of a power supply. Apart from circuits that protect ICs, most applications using a fast-acting fuse can switch to a time-lag fuse to improve immunity to interference; conversely, replacing a time-lag fuse with a fast-acting fuse often makes the fuse open at power-on, so the equipment cannot work normally.
 
 
The analysis above should give you a deeper understanding of fast-acting and time-lag fuses. In an earlier article we also discussed this question: Whether a Time-Lag Fuse Performs Better Than a Fast-Acting Fuse. If you have any other questions, please leave a message on our Contact Us page and we will reply as soon as possible.

上一条:已经是第一条了!

下一条:自恢复保险丝为什么用高分子材料制作?