Electronic components testing: what experience and techniques are there? Most faults encountered in electronic equipment come down to a failed component, so knowing how to test components correctly matters a great deal. Below we outline some common experience and techniques for testing electronic components.
1. Checking the polarity of bridge rectifier leads: set the multimeter to R×1k and connect the black probe to any lead of the bridge. Touch the red probe to the other three leads in turn. If every reading is infinite, the lead under the black probe is the positive output of the bridge; if the reading is 4–10kΩ, the lead under the black probe is the negative output and the remaining two leads are the AC inputs. (Related reading: Can fuses be connected in parallel?)
2. Judging whether a crystal is good: first measure the resistance across the crystal with a multimeter on the R×10k range. An infinite reading means the crystal is neither shorted nor leaking. Then insert a neon test screwdriver into a mains socket, hold one lead of the crystal between your fingers and touch the other lead to the metal tip of the screwdriver. If the neon lamp glows red, the crystal is good; if it stays dark, the crystal is defective.
3. Testing a unidirectional thyristor (SCR): use the R×1k or R×100 range of a multimeter to measure the forward and reverse resistance between any two terminals. If one pair of terminals reads a low resistance (about 100Ω to a few kΩ), the terminal under the black probe is the gate, the terminal under the red probe is the cathode and the remaining one is the anode. A thyristor contains three PN junctions, so its condition can be judged from the forward and reverse resistance of those junctions. When measuring between the gate (G) and the cathode (C), a reading of zero or infinity in both directions indicates a shorted or open gate; when measuring between the gate (G) and the anode (A), both the forward and reverse readings should be very high;
4. When measuring the resistance between the anode (A) and the cathode (C), both the forward and reverse readings should be very high.
5. Identifying the terminals of a triac: a triac has main terminal 1, main terminal 2 and a gate. Measured on the R×1k range, the resistance between the two main terminals should be close to infinity, whereas the forward and reverse resistance between the gate and either main terminal is only a few tens of ohms. (Recommended reading: Resettable fuse performance parameters)
This behaviour makes it easy to pick out the gate of a triac simply by measuring the resistance between terminals. With the black probe on main terminal 1 and the red probe on the gate, the forward resistance measured is always somewhat lower than the reverse resistance, which in turn makes it easy to tell main terminal 1 from main terminal 2 by resistance alone.
6. Checking a light-emitting digital display: set the multimeter to R×10k or R×100k and connect the red probe to the “ground” lead of the display (a common-cathode display is taken as the example here). Touch the black probe to each of the other leads in turn; all seven segments should light individually. If they do not, the display is faulty.
7. Identifying the electrodes of a junction FET: set the multimeter to R×1k and touch the black probe to the pin assumed to be the gate (G), then touch the red probe to each of the other two pins in turn. If both readings are fairly low (5–10Ω), swap the red and black probes and measure again. If both readings are now high (∞), they are reverse resistances (reverse-biased PN junction), the device is an N-channel FET, the pin under the black probe is the gate (G) and the original assumption was correct. If the second measurement still gives very low readings, they are forward resistances, the device is a P-channel FET and the pin under the black probe is again the gate (G).
If neither case occurs, swap the red and black probes and repeat the procedure until the gate is identified. The source and drain of a junction FET are symmetrical by construction, so once the gate (G) is known the source (S) and drain (D) need not be distinguished, because the two terminals are interchangeable. The resistance between source and drain is a few thousand ohms.
8. Identifying the electrodes of a transistor: for a transistor whose type marking is unclear or missing, a multimeter can still be used to sort out the three electrodes. First set the range switch to the R×100 or R×1k resistance range. Touch the red probe to one electrode and the black probe to the other two in turn, measuring the resistance each time. If both readings are a few hundred ohms (low resistance), the electrode under the red probe is the base (b) and the device is a PNP transistor. If both readings are from tens of kilohms up to a hundred kilohms or more (high resistance), the electrode under the red probe is again the base (b) and the device is an NPN transistor. (Recommended reading: Protective role of fuses in automotive electronic devices)
Once the device type and the base (b) are known, the collector can be found from the fact that a transistor's forward current gain is larger than its reverse current gain. Assume arbitrarily that one electrode is c and the other is e, and set the range switch to the R×1k resistance range. For a PNP device, connect the red probe to c and the black probe to e, then pinch the b and c leads together with your fingers, without letting them touch each other, and note the resistance. Swap the two probes and measure a second time, then compare the two readings: for a PNP device, the electrode under the red probe in the measurement with the lower resistance is the collector; for an NPN device, the electrode under the black probe in the measurement with the lower resistance is the collector.
9. Judging whether a potentiometer is good: first measure its nominal resistance. Using the ohmmeter range across terminals “1” and “3” (with terminal “2” as the wiper), the reading should equal the nominal value. If the pointer does not move, the resistance does not change, or the resistance is far off the nominal value, the potentiometer is faulty.
Next check that the wiper makes good contact with the resistive track. Measure across terminals “1” and “2” or across “2” and “3” with the ohmmeter range, turning the shaft anticlockwise to a position close to “off”; here the resistance should be as low as possible. Turn the shaft slowly clockwise: the resistance should increase gradually and, at the end of travel, come close to the nominal value. If the pointer jumps while the shaft is being turned, the wiper contact is poor.
10. Measuring the leakage resistance of a large-value capacitor: set a model 500 multimeter to the R×10 or R×100 range and, once the pointer reaches its maximum, switch immediately to R×1k. The pointer then settles within a short time, and the leakage resistance can be read off. (Related reading: Trip current characteristics and recovery behaviour of resettable fuses)
So what experience and techniques are there for testing electronic components? We hope this introduction has given you a clearer understanding of electronic components. If anything is still unclear, leave a message for us on the Contact Us page of our website and we will reply as soon as possible.