
Bourns 3224W-1-102E 4.0×4.0×2.5 mm 12-turn trimmer potentiometer, 1 kΩ, tolerance ±10%, 0.25 W power rating. For on-board bias, reference and zero calibration.
The 3224W-1-102E is a 4.0×4.0×2.5 mm surface-mount multiturn trimming potentiometer rated 1 kΩ ±10 %, with 12 turns end to end and a 0.25 W power rating. The element is cermet and the adjustment slot sits in the centre of the top face; the terminals reflow solder. Used for calibration points on a PCB that each unit has to be set to.
| Parameter | Value |
| Series | 3224 |
| Nominal resistance | 1 kΩ |
| Resistance tolerance | ±10 % |
| Power rating | 0.25 W |
| Turns | 12 turns |
| Linearity | — |
| Temperature coefficient | ±100 ppm/℃ |
| Mechanical rotation | 4320 ° |
| Dimensions | 4.0×4.0×2.5 mm |
| Model | Resistance | Tolerance | Power |
| 3224W-1-103E | 10 kΩ | ±10 % | 0.25 W |
| 3224W-1-502E | 5 kΩ | ±10 % | 0.25 W |
The 3224W-1-102E is a surface-mount multiturn trimmer that sets a voltage or current on the board to its design value. Twelve turns provide the fine adjustment margin: one movement of the screwdriver changes one twelfth of the 1 kΩ full scale. Boards that need each unit set at production use this part.
Body 4.0×4.0×2.5 mm, terminals on the two side pads, footprint laid out to the EIA 4 mm trimmer pattern. The adjustment slot sits in the centre of the top face, 0.6 mm wide and 0.5 mm deep, driven by a 0.6 mm flat blade or the H-91 tool. Resistance code and date code are marked on top.
The three terminals are the two ends of the cermet element and the wiper. As the wiper moves, resistance from terminal 1 to 2 falls while terminal 2 to 3 rises by the same amount. An internal lead screw reduces the motion, so one turn covers one twelfth of full scale, and the wiper idles past either end.
In the part number, 102 is the resistance code: the first two digits 10 are the significant figures and the third digit 2 means × 10², so 1 kΩ; 103 is 10 kΩ. Work out full scale first, then check power: at 1 kΩ the 0.25 W rating allows only 15.8 V at 15.8 mA. Tolerance ±10 % is ±100 Ω.
The full datasheet is on page 1 and can be downloaded from this page, covering electrical characteristics, environmental tests, outline dimensions and tape drawings. Operating range -65 °C to +150 °C, temperature coefficient ±100 ppm/°C, mechanical life 200 full cycles. For lot marking or an alternative part, contact our sales team.
The 0.25 W figure is the rating at 85 °C. Across a 1 kΩ full scale, √(0.25 W × 1 kΩ) = 15.8 V at 15.8 mA. The 300 V in the datasheet is the terminal withstand voltage; on low-resistance values the power limit arrives first. On a 24 V loop, put a fixed resistor in front to take part of the drop, or order the 103.
The 1 kΩ full scale spread over 12 turns gives 83 Ω per turn, 0.23 Ω per degree. Contact resistance variation of 1 % is 10 Ω, about 43° of rotation. When a setpoint has to land within 0.1 %, take up most of the range with fixed resistors and let this part trim the last step.
The top face carries the resistance code and the date code. 102 is 1 kΩ and 103 is 10 kΩ, a factor of 10 apart, with only the last digit different. The E tape for the W style holds 250 pcs per reel, so sort mixed reels by the top mark and check incoming lots against the code, not the reel label.
Up Page:Is the first!
Next Page:Bourns 3224W-1-103E Trimmer Potentiometer 10 kΩ 3224 Series