Shenzhen JDT Fuse Industrial Co.,Ltd

Phone : 0755-8830-8258

Postcode : 518129

E-Mail : andyzheng@jdtfuse.com

URL : http://www.joincircuit.com/

How to Achieve Optimal PCB Heat Dissipation

How to achieve optimal heat dissipation on a PCB - a printed circuit board (PCB), also called a printed wiring board, provides the electrical connections for electronic components. Its history goes back more than 100 years, its design is essentially a layout design, and its main advantage is that it greatly reduces wiring and assembly errors while raising the level of automation and production efficiency.
 
 
In recent years the use of PCBs has grown steadily, yet heat dissipation in the board's own design has always been a subject of study for engineers, and how to make a PCB dissipate heat as well as possible has become one of the most closely followed topics. (Related reading: Resettable fuse protection in no-smoking signs)
 
 
How to achieve optimal heat dissipation on a PCB - the heat in a PCB comes mainly from three sources: heat generated by the electronic components, heat generated by the board itself, and heat transferred from other parts. Component heat generation is the dominant source, so to obtain good heat dissipation we can work on the following aspects.
 
 
A: Dissipate heat through the PCB itself. The laminates in wide use today are copper-clad epoxy-glass cloth or phenolic-resin glass cloth, with a small amount of paper-based copper-clad laminate. These materials conduct heat poorly, so there is little point in relying on the board resin as the heat path for high-dissipation components; the best approach is to improve the heat-spreading capability of the PCB area in direct contact with the heat-generating components and conduct or radiate the heat out through the board.
 
 
B: Fit heatsinks and heat-spreader plates to high-dissipation devices. When fewer than three devices on a board dissipate a lot of heat, fit heatsinks or heat pipes to them; if the temperature still does not come down, use fan-cooled heatsinks to boost the cooling effect. When more than three devices dissipate heat, use a large heat shroud (plate): either a dedicated heatsink made to suit the position and height of the heat-generating devices on that board, or a large flat heatsink milled out at different heights to clear the various components. The shroud is clipped over the component side as a whole and dissipates heat through contact with each component. Because component heights vary after soldering, the cooling effect is often poor, so a soft phase-change thermal pad is usually added over the components to improve it.
 
 
C: Dissipate heat through sensible routing. The resin in the laminate conducts heat poorly, whereas copper traces and vias are good thermal conductors, so raising the copper retention rate and adding thermal vias are the main means of cooling. (Recommended reading: How to fix a laptop that will not charge)
 
 
D: When high-dissipation devices are mounted on the substrate, the thermal resistance between them and the board should be reduced as far as possible. To better meet the thermal requirements, apply a thermally conductive material to the underside of the chip (a layer of thermal grease, for example) and keep a contact area large enough for the device to dissipate heat.
 
 
E: In the horizontal direction, place high-power devices as close to the board edge as possible to shorten the heat path; in the vertical direction, place them as high on the board as possible so that the heat they produce has less effect on the temperature of neighbouring devices.
 
 
F: Cooling of the boards inside equipment depends mainly on airflow, so the airflow path has to be studied at the design stage and the components or boards arranged to suit it. Air always tends to flow where resistance is lowest, so when placing components on a board, avoid leaving a large empty area in one region. The same point applies to the arrangement of several boards within one unit.
 
 
G: Temperature-sensitive devices are best placed in the coolest region (the bottom of the enclosure, for example). Never place them directly above a heat-generating device, and when there are several of them, stagger them in the horizontal plane.
 
 
H: Avoid concentrating hot spots on the PCB. Spread the power as evenly as possible over the board and keep the surface temperature uniform and consistent. A strictly even distribution is often hard to achieve in practice, but regions of very high power density must be avoided so that an overheated spot does not disturb the normal operation of the whole circuit. (Recommended reading: How smart wearable products deliver a good experience)
 
 
How to achieve optimal heat dissipation on a PCB - to get better cooling results, choose the measures that suit the actual situation when designing the board. That is a brief summary of how to achieve optimal heat dissipation on a PCB; if anything is still unclear, leave a message for us on the contact page and we will reply as soon as possible.