≡ Param Finder by package / current / voltage
伯恩斯MF-MSMF010-2 自恢复保险丝 0.10A 60V 1812封装
上一张
  • 伯恩斯MF-MSMF010-2 自恢复保险丝 0.10A 60V 1812封装
下一张

Bourns MF-MSMF010-2 Resettable Fuse 0.10A 60V 1812

0.10 A hold current, 60 V maximum voltage, 1812 (4532) package, AEC-Q200 qualified. Post-trip resistance is 15 Ω maximum — size the downstream circuit against that value.

Download

0

The MF-MSMF010-2 is a 1812 surface-mount resettable fuse that carries 0.10 A continuously and withstands 60 V maximum. It measures 4.5 × 3.2 mm, has gold-plated terminals and suits reflow soldering. UL, CSA and TÜV recognised, AEC-Q200 qualified, RoHS compliant. Commonly used for overcurrent protection on 24 V and 48 V control boards, communication equipment and automotive modules.

Brand:BOURNS (Joincircuit is an authorised distributor)
Category:Resettable fuse / SMD, 1812 SMD (4532 mm)
Voltage:60 V; Current:hold 0.1 A; trip 0.3 A.

Specifications

ParameterValue
Hold current0.1 A
Trip current0.3 A
Maximum voltage60 V
Maximum fault current40 A
Initial resistance0.7 Ω
Post-trip max resistance15 Ω
Trip current / time0.5 A / 1.5 s
Dissipated power0.8 W
Package1812 SMD (4532 mm)

Temperature Derating

-40℃-20℃0℃23℃40℃50℃60℃70℃85℃
Hold current (A)0.160.140.120.10.080.070.060.050.03
Share of 23 °C rating160%140%120%100%80%70%60%50%30%

Product Description

What this product is

The MF-MSMF010-2 is a polymer resettable fuse connected in series to limit circuit current. Once the fault is cleared and the part cools, it conducts again, so the board does not have to come out for rework. A one-time fuse has to be replaced each time it opens.

Dimensions and appearance

1812 package, 4532 in metric, 4.5 mm long, 3.2 mm wide and 0.75 mm high. Gold-plated terminals, black body, model code and production lot marked on top. All 18 models in this series fit this one footprint, so a change of model needs no pad revision. Supplied on tape and reel for pick-and-place; hand soldering is also suitable.

How it works

It sits in series between the supply and the load. At 0.10 A its own resistance is 0.70 Ω, which gives a drop of 0.07 V across it. Above 0.30 A, or as ambient temperature rises, the internal material expands with heat, resistance climbs and the current is held to a low value.

After the fault is cleared

When the part cools after a trip, resistance falls back to the low state and the circuit runs again with no manual reset. After one trip the resistance is at most 15.00 Ω, 21 times the 0.70 Ω factory value, which gives 1.50 V at 0.10 A. The 15.00 Ω figure is the limit after repeated trips.

Parameters and selection

The full datasheet is available for download on this page and covers the derating table, time-current curves and package dimensions. At 60 °C inside an enclosure the hold current falls to 0.06 A; size the load against that figure. For lot confirmation, stock, or a 60 V alternative in the same current class, contact our sales team.

Selection Notes

1. After one trip it becomes a 15 Ω resistor

A new part measures 0.70 Ω, which gives 0.07 V at 0.10 A. The post-trip limit is 15.00 Ω, which gives 1.50 V at the same current, and that 1.50 V appears across the downstream circuit. A circuit that senses state through a resistor divider will see the divider shift and may report a fault that does not exist. Confirm that the downstream circuit accepts 15 Ω in series before specifying this part.

2. 0.10 A is a 23 °C figure

The 0.10 A rating holds at 23 °C ambient. At 60 °C inside an enclosure the part carries 0.06 A; at 85 °C it carries 0.03 A. A board drawing 0.08 A passes on the bench and opens by itself once it sits in a 60 °C enclosure. Calculate the load current from the derating table at the highest enclosure temperature.

3. 60 V is why this part gets specified

Among the 0.10 A parts in this series only this one is rated 60 V. A 24 V battery reaches 28.8 V while charging and 48 V telecom supplies see higher surges, which leaves a 30 V part with very little margin; one surge breaks it down, and a broken-down part goes open and takes the whole board down. Use this part above 24 V at 0.10 A; below 12 V a lower-voltage model costs less, ask our sales team.