
0.30 A hold current, 30 V maximum voltage, 1812 (4532) package. Its 10 A interrupt rating is the lowest in the entire se
The MF-MSMF030-2 is an 1812 surface-mount resettable fuse with a 0.30 A hold current and a 30 V maximum voltage. It measures 4.5 × 3.2 mm, has gold-plated terminals, and is suitable for reflow soldering. UL, CSA and TÜV recognised, RoHS compliant. Its 10 A interrupt rating is the lowest in the series, so it belongs on USB supplies and on-board regulators that are already current-limited.
| Parameter | Value |
| Hold current | 0.3 A |
| Trip current | 0.6 A |
| Maximum voltage | 30 V |
| Maximum fault current | 10 A |
| Initial resistance | 0.3 Ω |
| Post-trip max resistance | 3 Ω |
| Trip current / time | 8 A / 0.1 s |
| Dissipated power | 0.8 W |
| Package | 1812 SMD (4532 mm) |
| -40℃ | -20℃ | 0℃ | 23℃ | 40℃ | 50℃ | 60℃ | 70℃ | 85℃ | |
| Hold current (A) | 0.44 | 0.39 | 0.35 | 0.3 | 0.26 | 0.23 | 0.21 | 0.18 | 0.15 |
| Share of 23 °C rating | 147% | 130% | 117% | 100% | 87% | 77% | 70% | 60% | 50% |
The MF-MSMF030-2 is a polymer resettable fuse with a 0.30 A hold current and a 30 V maximum voltage. The 0.30 A step fills the gap between the 0.20 A and 0.50 A parts and fits loads of about 0.25 A. After a trip and a cooldown it returns to conduction by itself, with no manual reset.
1812 package, 4532 in metric, 4.5 mm long, 3.2 mm wide and 0.75 mm high. Gold-plated terminals at both ends, black body, with the model code and production lot marked on top. Supplied on tape and reel for automatic pick-and-place, and also suitable for hand soldering. The footprint matches the other 1812 parts in the series, so a change of model needs no board revision.
The fuse sits in series with the circuit. At 23 °C and 0.30 A it presents 0.30 Ω, which is 0.09 V across it, a small share of a 5 V or 12 V supply. Above 0.60 A the internal material expands with heat and its resistance rises sharply, limiting the current to a small value. At 8.0 A it opens within 0.10 s.
When power is removed or the fault disappears and the part cools, it returns to its low-resistance state and the circuit resumes normal operation. Post-trip resistance is 3.0 Ω maximum, which is 0.9 V at 0.30 A. On a 5 V rail that is 18% of the supply, so re-measure the supply voltage at the load after a trip.
Full parameters are in the datasheet, downloadable from this page, including temperature derating, time-current curves and package dimensions. Work out the prospective fault current before specifying this part, because anything above 10 A rules it out. For lot confirmation, stock enquiries or parameter-based alternatives, please contact our sales team.
Interrupt rating is the largest current the fuse can break safely. Most parts in this series carry 40 A or 100 A, and this one carries 10 A. Above 10 A it may puncture or crack before the trip completes, or carbonise into conduction, and the protection is gone. A rail fed straight from a 12 V battery delivers tens of amperes into a short, and this part provides no protection there.
By hold current the ladder runs 0.20 A, 0.30 A and 0.50 A. At a 0.25 A load the 0.20 A part leaves 25% margin, and the 0.50 A part only opens once the current reaches 1.00 A, which is coarse for small faults. The 0.30 A part covers that range. The cost is interrupt rating, 80 A down to 10 A, so fault current still has to be checked once the current matches.
The Joincircuit ASMD1812-030 is also 0.30 A with 3.0 Ω maximum post-trip resistance, the same as this part. Its 30 V version carries a 100 A interrupt rating, ten times that of this fuse. Resistance and derating curve are close, so the voltage drop on the board needs no recalculating.