
0.75 A hold current, 24 V maximum voltage, 1812 (4532) package. Same current and resistance as the 075, with the voltage
The MF-MSMF075/24-2 is a 1812 surface-mount resettable fuse that carries 0.75 A continuously and withstands 24 V maximum. It measures 4.5 × 3.2 mm, has gold-plated terminals and suits reflow soldering. UL, CSA and TÜV recognised, RoHS compliant. The 24 after the slash is the voltage rating, twice that of the 0.75 A MF-MSMF075-2; commonly used on 24 V battery-fed automotive modules, industrial control boards and communication equipment.
| Parameter | Value |
| Hold current | 0.75 A |
| Trip current | 1.5 A |
| Maximum voltage | 24 V |
| Maximum fault current | 40 A |
| Initial resistance | 0.11 Ω |
| Post-trip max resistance | 0.45 Ω |
| Trip current / time | 8 A / 0.2 s |
| Dissipated power | 0.8 W |
| Package | 1812 SMD (4532 mm) |
| -40℃ | -20℃ | 0℃ | 23℃ | 40℃ | 50℃ | 60℃ | 70℃ | 85℃ | |
| Hold current (A) | 1.15 | 1.01 | 0.88 | 0.75 | 0.65 | 0.6 | 0.55 | 0.49 | 0.43 |
| Share of 23 °C rating | 153% | 135% | 117% | 100% | 87% | 80% | 73% | 65% | 57% |
| Model | Vmax | R1max | Package | Note |
| MF-MSMF075 | 13.2 V | 0.45 Ω | 1812 SMD (4532 mm) |
The MF-MSMF075/24-2 is a polymer resettable fuse connected in series between a supply and its load. Above 1.50 A the internal material expands with heat, resistance rises and the current is held to a low value. Once the fault is cleared and the part cools it conducts again, so no board comes out for rework. At 0.75 A it suits fans, relay coils and small motors.
1812 package, 4532 in metric, 4.5 mm long, 3.2 mm wide and 0.75 mm high. Gold-plated terminals, black body, model code and production lot marked on top. The body is identical to the MF-MSMF075-2 without a suffix, so only the reel label separates them; check it at goods-in and at every reel change.
It sits in series in the loop. At 23 °C and 0.75 A its own resistance is 0.11 Ω, which gives a drop of 0.08 V, 0.7% of a 12 V supply. Above 1.50 A, or as ambient temperature rises, the internal material expands with heat, resistance climbs and the current is limited. At 8 A it opens within 0.20 s.
When the part cools after a trip, resistance falls back to the low state and the loop runs again with no manual reset. After one trip the resistance is at most 0.45 Ω, four times the 0.11 Ω factory value, which gives 0.34 V at 0.75 A. Repeated trips stay within 0.45 Ω; check the downstream circuit against 0.34 V.
The full datasheet is available for download on this page and covers the derating table, time-current curves and package dimensions. At 60 °C inside an enclosure the hold current is 0.55 A, and 0.43 A at 85 °C. A 24 V battery reaches 28.8 V, so check the margin against that figure. For lot confirmation or a comparison with the 13.2 V part, contact our sales team.
Current and resistance are identical across the two parts: 0.75 A, 0.11 Ω new and 0.45 Ω after a trip. Voltage and interrupt rating differ: the 13.2 V part clears 100 A, this one clears 40 A. Where the supply itself limits fault current below 40 A, the change costs nothing; on a battery rail where fault current runs to a hundred amps, work the number out before switching.
Take the highest voltage the loop can reach, the larger of the battery's full-charge value and the supply's switching transient, and compare it with 13.2 V. A 24 V battery reaches 28.8 V and a 24 V switch-mode supply spikes past 30 V; the 13.2 V part breaks down at the first such event and goes open, taking the board down. Use this part above 13 V, and the 13.2 V part below it.
Bourns stops at 24 V in this current class. Joincircuit's ASMD1812-075-48V is rated 48 V, clears 40 A and carries a post-trip limit of 0.50 Ω, 0.05 Ω above the 0.45 Ω here. Moving a 48 V loop onto it keeps the current and the pads, but the drop has to be recalculated at 0.50 Ω, and the derating curves need checking again.