
1.60 A hold current, 8 V maximum voltage, 1812 (4532) package. Post-trip resistance is 0.099 Ω — the first part in the f
The MF-MSMF160-2 is a 1812 surface-mount resettable fuse that carries 1.60 A continuously and withstands 8 V maximum. It measures 4.5 × 3.2 mm, has gold-plated terminals and suits reflow soldering. UL, CSA and TÜV recognised, RoHS compliant. The 8 V ceiling places it on 5 V rails, commonly for USB ports, 5 V supply branches and on-board 5 V loads.
| Parameter | Value |
| Hold current | 1.6 A |
| Trip current | 2.8 A |
| Maximum voltage | 8 V |
| Maximum fault current | 100 A |
| Initial resistance | 0.035 Ω |
| Post-trip max resistance | 0.099 Ω |
| Trip current / time | 8 A / 2 s |
| Dissipated power | 0.8 W |
| Package | 1812 SMD (4532 mm) |
| -40℃ | -20℃ | 0℃ | 23℃ | 40℃ | 50℃ | 60℃ | 70℃ | 85℃ | |
| Hold current (A) | 2.3 | 2.2 | 1.9 | 1.6 | 1.45 | 1.3 | 1.15 | 1.03 | 0.91 |
| Share of 23 °C rating | 144% | 138% | 119% | 100% | 91% | 81% | 72% | 64% | 57% |
The MF-MSMF160-2 is a polymer resettable fuse connected in series between a supply and its load to limit current. The hold current, the current it carries continuously, is 1.60 A here, enough for a load of 1 A to 1.3 A such as two USB ports, a 5 V drive supply or several 5 V branches on one board. It recovers by itself, so no board comes out for a replacement.
1812 package, 4532 in metric, 4.5 mm long, 3.2 mm wide and 0.75 mm high. Gold-plated terminals, black body, marked 16. The other 8 V part on this footprint is the 2.00 A MF-MSMF200-2, marked 20, and the two look the same; confirm the model on the reel label at goods-in.
It sits in series in the loop. At 23 °C and 1.60 A its own resistance is 0.035 Ω, a drop of 0.056 V, about 1% of a 5 V rail. Above 2.80 A the internal material expands with heat, resistance climbs and the current is held. At a fault current of 8 A it opens within 2.0 s.
When the part cools after a trip, resistance falls back and the loop runs again with no manual reset. After one trip the resistance is at most 0.099 Ω, 2.8 times the 0.035 Ω factory value, which gives 0.158 V at 1.60 A, about 3% of a 5 V rail. Size the downstream chip against that 0.16 V drop.
The full datasheet is available for download on this page and covers the derating table, time-current curves and package dimensions. At 60 °C inside an enclosure the hold current is 1.15 A, and 0.91 A at 85 °C. Above 8 V this class cannot be used; choose a higher-voltage model, and contact our sales team for lot confirmation or an alternative.
A 5 V adapter sits at 5.2 V with no load and rises a little higher while a plug goes in, so the 8 V ceiling leaves 2.8 V of margin. A branch fed from 12 V cannot use this part: the first power-up breaks it down, and a broken-down part goes open and takes the whole board down. Measure the highest voltage the rail ever reaches before specifying it.
The 8 V group holds this 1.60 A part and the 2.00 A MF-MSMF200-2, with nothing smaller. Below 1.2 A the choice falls back to the 6 V MF-MSMF125-2, which leaves just 1 V of margin on a 5 V rail. Above 2 A the next step is a 16 V or 24 V model instead.
At a fault current of 8 A on a 5 V rail the part opens within 2.0 s, and 8 A flows for that whole time. Connectors, PCB traces and the MOSFET ahead of it have to be sized for 8 A over 2 s; thin traces give out before the fuse opens. Opening time stretches as current falls, so read the time-current curve in the datasheet near 3 A.