
2.00 A hold current, 8 V maximum voltage, 1812 (4532) package. It holds 62% of rating at 85 °C, the best high-temperatur
The MF-MSMF200-2 is a 1812 surface-mount resettable fuse that carries 2.00 A continuously and withstands 8 V maximum. It measures 4.5 × 3.2 mm, has gold-plated terminals and suits reflow soldering. UL, CSA and TÜV recognised, RoHS compliant. The 8 V ceiling limits it to 5 V rails, commonly for USB 3.0 ports, 5 V power distribution and multi-branch 5 V loads.
| Parameter | Value |
| Hold current | 2 A |
| Trip current | 4 A |
| Maximum voltage | 8 V |
| Maximum fault current | 40 A |
| Initial resistance | 0.02 Ω |
| Post-trip max resistance | 0.08 Ω |
| Trip current / time | 8 A / 3 s |
| Dissipated power | 0.8 W |
| Package | 1812 SMD (4532 mm) |
| -40℃ | -20℃ | 0℃ | 23℃ | 40℃ | 50℃ | 60℃ | 70℃ | 85℃ | |
| Hold current (A) | 3.08 | 2.71 | 2.35 | 2 | 1.8 | 1.6 | 1.5 | 1.4 | 1.25 |
| Share of 23 °C rating | 154% | 136% | 118% | 100% | 90% | 80% | 75% | 70% | 62% |
The MF-MSMF200-2 is a polymer resettable fuse connected in series between a supply and its load to limit current. The hold current, the current it carries continuously, is 2.00 A, third largest in the series behind the 2.50 A and 2.60 A parts. It carries a load of about 1.5 A such as a USB 3.0 port, the 5 V input of a multi-port charger or a drive backplane branch.
1812 package, 4532 in metric, 4.5 mm long, 3.2 mm wide and 0.75 mm high. Gold-plated terminals, black body, marked 20. The 1.60 A MF-MSMF160-2, marked 16, shares the footprint and the 8 V rating and looks the same; confirm the model on the reel label at goods-in.
It sits in series in the loop. At 23 °C and 2.00 A its own resistance is 0.020 Ω, a drop of 0.040 V, about 0.8% of a 5 V rail. Above 4.00 A the internal material expands with heat and the current is held. At a fault current of 8 A it opens within 3.0 s.
When the part cools after a trip, resistance falls back and the loop runs again with no manual reset. After one trip the resistance is at most 0.080 Ω, 4 times the 0.020 Ω factory value, which gives 0.16 V at 2.00 A, about 3% of a 5 V rail. Size the downstream chip against that 0.16 V drop.
The full datasheet is available for download on this page and covers the derating table, time-current curves and package dimensions. At 60 °C inside an enclosure the hold current is 1.50 A, and 1.25 A at 85 °C. Above 8 V this class cannot be used; contact our sales team for lot confirmation or an alternative model.
The rating is 2.00 A at 23 °C and 1.25 A at 85 °C, 62% of nominal. At the same 85 °C the 1.60 A part keeps 0.91 A and the 1.50 A MF-MSMF150/24X-2 keeps 0.69 A. Holding on to that much at heat comes with an 8 V ceiling, so the part only fits 5 V rails. Where a 5 V rail must carry above 1.3 A in an enclosure above 70 °C, this class has the widest margin.
The interrupt rating, the largest fault current the part can safely break, is 40 A here. A 5 V supply module can deliver more than 60 A into a short, and above 40 A this part cannot break the fault; it keeps heating until the body cracks. Add current limiting ahead of it, or choose a model rated 100 A, as the 1.60 A part is.
This part opens at 4.00 A, twice its 2.00 A hold current, while the 1.60 A part trips at 1.75 times its rating. A board whose load swings around 2.5 A never opens this part and never cools down either, so it sits between states, resistance creeps up and the drop grows. Check the trip point at 4.00 A and limit sustained overload ahead of the part.