≡ Param Finder by package / current / voltage
MF-PSMF050X 0805 贴片自恢复保险丝
上一张
  • MF-PSMF050X 0805 贴片自恢复保险丝
下一张

Bourns MF-PSMF050X Resettable Fuse 0.50A 6V 0805 SMD

Bourns MF-PSMF050X SMD resettable fuse, 0.50 A hold current, 6 V maximum voltage, 0805 package. Self-resetting after the fault is cleared, no replacement needed.

Download

0

The MF-PSMF050X is a 0805 surface-mount resettable fuse that carries 0.50 A continuously and withstands 6 V maximum. The body measures 2.00–2.30 mm long, 1.20–1.50 mm wide and 0.48–0.85 mm high, with gold-plated terminals for reflow soldering. UL recognised, RoHS compliant. Commonly used for overcurrent protection on USB 2.0 and USB 3.0 ports and on motherboard plug-and-play circuits.

Brand:BOURNS (Joincircuit is an authorised distributor)
Category:Resettable fuse / SMD, 0805 SMD (2012 mm)
Voltage:6 V; Current:hold 0.5 A; trip 1 A.

Specifications

ParameterValue
Hold current0.5 A
Trip current1 A
Maximum voltage6 V
Maximum fault current40 A
Initial resistance0.15 Ω
Post-trip max resistance0.9 Ω
Trip current / time8 A / 0.1 s
Dissipated power0.5 W
Package0805 SMD (2012 mm)

Temperature Derating

-40℃-20℃0℃23℃40℃50℃60℃70℃85℃
Hold current (A)0.680.620.550.50.40.370.330.290.23
Share of 23 °C rating136%124%110%100%80%74%66%58%46%

Product Description

What this product is

The MF-PSMF050X is a polymer resettable fuse wired in series between a 5 V bus and its load. The 0805 body is 2.30 mm long at most, which suits USB ports, where space is tight and cables go in and out all day. A short at the connector or a damaged cable trips the part, it recovers once the fault is cleared, and the unit does not come back for repair.

Dimensions and appearance

0805 package, 2012 in metric, body 2.00–2.30 mm long, 1.20–1.50 mm wide and 0.48–0.85 mm high. The six models in this footprint fall into two height groups; the 0.75 A and 1.10 A parts reach 1.25 mm and this 0.50 A part sits in the thin group. Nickel-plated terminals with a gold finish, one digit on top, a 4 on this part. 3000 parts per reel.

How it works

It sits in series between the 5 V bus and the load. At 0.50 A its own resistance is 0.150 Ω, which gives a drop of 0.075 V, 1.5 % of a 5 V bus. Above 1.00 A the internal material expands with heat, resistance climbs and the current is held to a low value. At a fault current of 8.00 A it opens within 0.10 s.

After the fault is cleared

When the part cools after a trip, resistance falls back to the low state and the loop runs again with no manual reset. After one trip the resistance is at most 0.900 Ω, six times the 0.150 Ω factory value, which gives 0.45 V at 0.50 A. A 5 V bus behind this part then sits at 4.55 V, and a USB device may reset or fail to enumerate.

Parameters and selection

The full datasheet is available for download on this page and covers the derating table, time-current curves and package dimensions. At 60 °C inside an enclosure the hold current is 0.33 A, and 0.23 A at 85 °C; size the load against those figures. A 5 V supply held to ±5 % reaches 5.25 V, which leaves 0.75 V below the 6 V rating. For lot confirmation or an alternative, contact our sales team.

Selection Notes

1. 6 V of standoff leaves 0.75 V on a 5 V bus

USB VBUS is allowed up to 5.25 V and this part is rated 6 V, which leaves 0.75 V of margin. The overshoot from a hot-plug event and cable inductance easily exceeds that, and one overvoltage can break the material down; a broken-down part goes open and the port fails. The MF-PSMF020X is rated 9 V and the MF-PSMF010X 15 V in the same footprint, at 0.20 A and 0.10 A. A TVS diode ahead of the part is the other common fix.

2. One trip costs 0.45 V on a 5 V bus

A new part measures 0.150 Ω, which gives 0.075 V at 0.50 A and is invisible. After one trip the limit is 0.900 Ω, six times higher, which gives 0.45 V at the same current. A 5 V bus behind it sits at 4.55 V, USB 2.0 asks for 4.40 V at the device, and a cable drop on top of that brings the port close to its floor. Work the voltage budget against 0.900 Ω.

3. Six models in one footprint, told apart by one digit

The 010X, 020X, 035X and 050X parts measure the same, 2.00–2.30 mm by 1.20–1.50 mm, and each carries one digit on top: 1, 2, 3 and 4. When a board is reworked, when parts arrive, or when a removed part is reused, one digit misread is the difference between 0.10 A and 0.50 A. Check the reel label against the part; the week code appears on the label only.