
Bourns 3224W-1-502E 4.0×4.0×2.5 mm 12-turn trimmer potentiometer, 5 kΩ, tolerance ±10%, 0.25 W power rating. For on-board bias, reference and zero calibration.
The 3224W-1-502E is a 4.0×4.0×2.5 mm surface-mount multiturn trimming potentiometer rated 5 kΩ ±10 %, 12 turns end to end, 0.25 W. Cermet element, flat-blade slot on the top face, 16 mm tape. Usually the adjustable leg of a divider, upper or lower.
| Parameter | Value |
| Series | 3224 |
| Nominal resistance | 5 kΩ |
| Resistance tolerance | ±10 % |
| Power rating | 0.25 W |
| Turns | 12 turns |
| Linearity | — |
| Temperature coefficient | ±100 ppm/℃ |
| Mechanical rotation | 4320 ° |
| Dimensions | 4.0×4.0×2.5 mm |
| Model | Resistance | Tolerance | Power |
| 3224W-1-102E | 1 kΩ | ±10 % | 0.25 W |
| 3224W-1-103E | 10 kΩ | ±10 % | 0.25 W |
The 3224W-1-502E is a surface-mount multiturn trimmer. At 5 kΩ it sits between the 1 kΩ and 10 kΩ parts, so a divider leg built on it keeps both the current and the adjustment margin in range. Twelve turns split it into 12 steps of 417 Ω, enough to set a calibration point.
Body 4.0×4.0×2.5 mm with surface-mount terminals on both ends, footprint to the EIA 4 mm trimmer pattern. The slot in the centre of the top face is 0.6 mm wide and 0.5 mm deep. The 502 code and date code are marked on top; one reel carries 250 pcs.
The wiper runs along the cermet element, so resistance from terminal 1 to 2 falls while 2 to 3 rises, and a divider tap follows the shaft angle. The 5 kΩ splits into 417 Ω per turn. Past either end the wiper idles and nothing jams.
In the part number, 502 is the resistance code: the first two digits 50 are the significant figures and the third digit 2 means × 10², so 5 kΩ; 103 is 10 kΩ. At 5 kΩ, 0.25 W allows 35.4 V at 7.1 mA. Tolerance ±10 % is ±500 Ω, or 1.2 turns of adjustment.
The full datasheet is on page 1 and can be downloaded from this page, covering electrical characteristics, environmental tests, outline dimensions and tape drawings. Operating range -65 °C to +150 °C, temperature coefficient ±100 ppm/°C, mechanical life 200 full cycles. For lot confirmation or an alternative, contact our sales team.
√(0.25 W × 5 kΩ) = 35.4 V at 7.1 mA. On a 24 V divider the upper leg draws 4.8 mA for 0.115 W, half the rating; on a 36 V bus the same 5 kΩ draws 0.26 W, past the 0.25 W limit, so go to 10 kΩ or two parts in series.
One degree is 1.16 Ω. The ±10 % tolerance of 500 Ω takes 1.2 turns to trim out, which the travel covers. Contact resistance variation of 1 % is 50 Ω, about 43° of rotation, and that jitter stays on the output after the setting is done.
The E tape for the 3224W carries 250 pcs and needs a 16 mm feeder. A 1000-board run takes four reels with spares. Check the 502 mark on top at each reel change, since the 102 and 103 parts in the same series look identical.