≡ Param Finder by package / current / voltage
3296W-1-502LF 5 kΩ 3296系列微调电位器
上一张
  • 3296W-1-502LF 5 kΩ 3296系列微调电位器
下一张

Bourns 3296W-1-502LF Trimmer Potentiometer 5 kΩ 3296 Series

Bourns 3296W-1-502LF 9.53×9.53×4.83 mm 25-turn trimmer potentiometer, 5 kΩ, tolerance ±10%, 0.5 W power rating. For on-board bias, reference and zero calibration.

Download

0

The 3296W-1-502LF is a 9.53×9.53×4.83 mm through-hole multiturn trimming potentiometer rated 5 kΩ ±10 % with 25 turns and 0.5 W. Top-face flat-blade slot, three pins on a 2.54 mm pitch, LF suffix for the 100 % tin-plated version. A divider built on this value keeps both current and adjustment margin comfortable.

Brand:BOURNS (Joincircuit is an authorised distributor)
Category:Trimmer potentiometer / 3296 系列
Resistance:5 kΩ;Power rating:0.5 W

Specifications

ParameterValue
Series3296
Nominal resistance5 kΩ
Resistance tolerance±10 %
Power rating0.5 W
Turns25 turns
Linearity—
Temperature coefficient±100 ppm/℃
Mechanical rotation9000 °
Dimensions9.53×9.53×4.83 mm

Other Resistances in This Series

ModelResistanceTolerancePower
3296W-1-103LF10 kΩ±10 %0.5 W
3296W-1-203LF20 kΩ±10 %0.5 W
3296W-1-202LF2 kΩ±10 %0.5 W

Product Description

What this product is

The 3296W-1-502LF is a through-hole multiturn trimmer. At 5 kΩ the 25 turns give 200 Ω per turn, half the step size of the 10 kΩ part in the same series, which suits very small output steps. Calibration points on a board use it where the working current is low.

Dimensions and appearance

Square body 9.53×9.53×4.83 mm, top slot 0.76 mm wide and 0.56 mm deep for the H-90 tool. Three pins 0.51 mm in diameter on a 2.54 mm pitch, soldered through the board. The top face carries the brand, the 502 code, the wiring diagram and the date code; standard pack is 50 pcs per tube.

How it works

Terminals 1 and 3 connect to the cermet element, terminal 2 is the wiper. The screw covers the whole range in 25 turns, 200 Ω per turn at 5 kΩ, and the wiper idles past either end. In a divider the tap voltage follows the angle while the 1-2 and 2-3 resistances move in opposite directions.

How to choose

In the part number, 502 is the resistance code: the first two digits 50 are the significant figures and the third digit 2 means × 10², so 5 kΩ; 103 is 10 kΩ. At 5 kΩ, 0.5 W allows 50 V at 10 mA. Tolerance ±10 % is ±500 Ω, or 2.5 turns of adjustment.

Parameters and documentation

The full datasheet is on page 1 and can be downloaded from this page, with the resistance table, environmental tests, outline and tape dimensions. Operating range -55 °C to +125 °C, temperature coefficient ±100 ppm/°C. For a packaging code (tube, tape and reel, ammo pack) or an alternative, contact our sales team.

Selection Notes

1. At 5 kΩ the 0.5 W rating tops out at 50 V

√(0.5 W × 5 kΩ) = 50 V at 10 mA. On a 24 V loop the 5 kΩ draws 4.8 mA for 0.115 W, more than four times inside the rating; derated to 0.36 W at 70 °C the voltage limit falls to 42 V.

2. Twenty-five turns across 5 kΩ leaves 200 Ω per turn

One degree is 0.56 Ω. The ±10 % tolerance of 500 Ω takes 2.5 turns, which the travel covers. Contact resistance variation of 1 % is 50 Ω, about 90° of rotation, and that jitter remains on the output once the setting is done.

3. Tubes hold 50 pcs, tape and reel needs the R code

Standard packaging is 50 pcs per tube. The W style can also ship on R tape and reel or in an A ammo pack, so put the packaging code on the order when the part goes onto a placement line. Default shipment is tubes, which the through-hole line stages by the tube.