≡ Param Finder by package / current / voltage
3296W-1-202LF 2 kΩ 3296系列微调电位器
上一张
  • 3296W-1-202LF 2 kΩ 3296系列微调电位器
下一张

Bourns 3296W-1-202LF Trimmer Potentiometer 2 kΩ 3296 Series

Bourns 3296W-1-202LF 9.53×9.53×4.83 mm 25-turn trimmer potentiometer, 2 kΩ, tolerance ±10%, 0.5 W power rating. For on-board bias, reference and zero calibration.

Download

0

The 3296W-1-202LF is a 9.53×9.53×4.83 mm through-hole multiturn trimming potentiometer rated 2 kΩ ±10 % with 25 turns and 0.5 W. Top-face flat-blade slot, three pins on a 2.54 mm pitch. At 2 kΩ this is the low-resistance end of the series, with only 80 Ω per turn.

Brand:BOURNS (Joincircuit is an authorised distributor)
Category:Trimmer potentiometer / 3296 系列
Resistance:2 kΩ;Power rating:0.5 W

Specifications

ParameterValue
Series3296
Nominal resistance2 kΩ
Resistance tolerance±10 %
Power rating0.5 W
Turns25 turns
Linearity—
Temperature coefficient±100 ppm/℃
Mechanical rotation9000 °
Dimensions9.53×9.53×4.83 mm

Other Resistances in This Series

ModelResistanceTolerancePower
3296W-1-103LF10 kΩ±10 %0.5 W
3296W-1-502LF5 kΩ±10 %0.5 W
3296W-1-203LF20 kΩ±10 %0.5 W

Product Description

What this product is

The 3296W-1-202LF is a through-hole multiturn trimmer, and 2 kΩ is the low end of the series with 80 Ω per turn, the finest step here. Low-resistance loops use it: the source impedance stays low, the following stage picks up less noise, and the higher wiper current helps keep the contact clean.

Dimensions and appearance

Square body 9.53×9.53×4.83 mm, top slot 0.76 mm wide and 0.56 mm deep for the H-90 tool. Three pins 0.51 mm in diameter on a 2.54 mm pitch, through-hole soldered. The top face carries the brand, the 202 code, the wiring diagram and the date code; tubes hold 50 pcs.

How it works

The wiper crosses the cermet element in 25 turns, 80 Ω per turn at 2 kΩ. Resistances 1-2 and 2-3 move in opposite directions and a divider tap follows the shaft angle. Past either end the wiper idles, so over-turning does no harm.

How to choose

In the part number, 202 is the resistance code: the first two digits 20 are the significant figures and the third digit 2 means × 10², so 2 kΩ; 103 is 10 kΩ. At 2 kΩ, 0.5 W allows 31.6 V at 15.8 mA. Tolerance ±10 % is ±200 Ω, or 2.5 turns of adjustment.

Parameters and documentation

The full datasheet is on page 1 and can be downloaded from this page, with the resistance table, environmental tests, outline and tape dimensions. Operating range -55 °C to +125 °C, temperature coefficient ±100 ppm/°C. For another value in the series or an alternative, contact our sales team.

Selection Notes

1. At 2 kΩ the 0.5 W rating stops at 31.6 V

√(0.5 W × 2 kΩ) = 31.6 V at 15.8 mA. A 5 V loop draws 2.5 mA through 2 kΩ for 0.013 W; a 24 V loop draws 12 mA for 0.29 W, and with the rating derated to 0.36 W at 70 °C that leaves under a fifth in reserve.

2. In two-wire use the wiper current counts

Used as a variable resistor, 15.8 mA runs through the wiper, and contact resistance variation of 1 % is 20 Ω, which puts 0.32 V of jump on the output. Wire it as a divider instead and the wiper current drops to nearly nothing, taking that figure down with it.

3. Twenty-five turns across 2 kΩ leaves 80 Ω per turn

One degree is 0.22 Ω, the finest of the four values in this series. The ±10 % tolerance of 200 Ω takes 2.5 turns, and screwdriver repeatability of 2° to 5° moves the setting by 0.44 Ω to 1.1 Ω, still fine enough to resolve a setpoint.