≡ Param Finder by package / current / voltage
3362P-1-103LF 10 kΩ 3362系列微调电位器
上一张
  • 3362P-1-103LF 10 kΩ 3362系列微调电位器
下一张

Bourns 3362P-1-103LF Trimmer Potentiometer 10 kΩ 3362 Series

Bourns 3362P-1-103LF 6.6×7.0×4.7 mm single-turn trimmer potentiometer, 10 kΩ, 0.5 W power rating. For on-board bias, reference and zero calibration.

Download

0

The 3362P-1-103LF is a 6.6×7.0×4.7 mm through-hole single-turn trimming potentiometer rated 10 kΩ with 0.5 W, adjusted from the top face over 240°. Three pins on a 2.54 mm pitch, through-hole soldered, LF suffix for the 100 % tin-plated version. Used for calibration points that are set once and rarely touched.

Brand:BOURNS (Joincircuit is an authorised distributor)
Category:Trimmer potentiometer / 3362 系列
Resistance:10 kΩ;Power rating:0.5 W

Specifications

ParameterValue
Series3362
Nominal resistance10 kΩ
Resistance tolerance—
Power rating0.5 W
TurnsSingle turn
Linearity—
Temperature coefficient±100 ppm/℃
Mechanical rotation270 °
Dimensions6.6×7.0×4.7 mm

Other Resistances in This Series

ModelResistanceTolerancePower
3362P-1-203LF20 kΩ—0.5 W

Product Description

What this product is

The 3362 is a 1/4 inch square single-turn trimmer: one sweep covers the whole range, which suits calibration points that do not need finer steps, such as supply sensing dividers, comparator thresholds and display brightness. It occupies 46 mm² against 91 mm² for the 9.53 mm multiturn part.

Dimensions and appearance

Body 6.6×7.0×4.7 mm with a cross slot on the top face, 2.77 mm long, 0.64 mm wide and 0.89 mm deep, driven by the H-90 tool. Three pins 0.46 mm in diameter on a 2.54 mm pitch, soldered through the board. The top face carries the resistance code, pin numbers 1 2 3, the model and the date code.

How it works

The wiper reaches either end in 240° of rotation, mechanical angle 270°, leaving 30° of idle travel across the two ends. The whole 10 kΩ from terminal 1 to 3 sits inside that one sweep, so the tap voltage moves with every degree and the position has to be set in one pass.

How to choose

In the part number, 103 is the resistance code: the first two digits 10 are the significant figures and the third digit 3 means × 10³, so 10 kΩ; 203 is 20 kΩ. At 10 kΩ, 0.5 W allows 70.7 V at 7.07 mA. The datasheet lists no resistance tolerance for this series, so contact us before relying on one.

Parameters and documentation

The full datasheet is on pages 1 and 2 and can be downloaded from this page, with the resistance table, environmental tests, outline dimensions and tape drawings. Operating range -55 °C to +125 °C, temperature coefficient ±100 ppm/°C. For a tolerance grade or the knob version, contact our sales team.

Selection Notes

1. At 10 kΩ the 0.5 W rating tops out at 70.7 V

√(0.5 W × 10 kΩ) = 70.7 V at 7.07 mA. A 12 V sensing divider draws only 1.2 mA for 0.014 W, and a 24 V loop draws 2.4 mA for 0.058 W, eight times inside the limit.

2. 240° across 10 kΩ leaves 41.7 Ω per degree

Screwdriver repeatability of 2° to 5° puts two settings of the same point 83 Ω to 208 Ω apart, and that is the error on the divider output. Where finer than that is needed, move from a single-turn part to a 12 or 25 turn type.

3. Wound to the stop, 100 Ω remains between 1 and 2

The datasheet end resistance is 1 % or 2 Ω, whichever is greater, which is 100 Ω on 10 kΩ, 1 % of full scale. Treating that stop as zero leaves the output 100 Ω high, so include the end resistance in the divider ratio.