
Bourns 3314J-1-102E 4.5×4.5×2.55 mm single-turn trimmer potentiometer, 1 kΩ, tolerance ±20%, 0.25 W power rating. For on-board bias, reference and zero calibration.
The 3314J-1-102E is a 4.5×4.5×2.55 mm surface-mount single-turn trimming potentiometer rated 1 kΩ ±20 % with 0.25 W. Top-face adjustment, J-hook terminals, 500 pcs per E reel. Chosen for fine steps on low-voltage loops.
| Parameter | Value |
| Series | 3314 |
| Nominal resistance | 1 kΩ |
| Resistance tolerance | ±20 % |
| Power rating | 0.25 W |
| Turns | Single turn |
| Linearity | — |
| Temperature coefficient | ±100 ppm/℃ |
| Mechanical rotation | 240 ° |
| Dimensions | 4.5×4.5×2.55 mm |
| Model | Resistance | Tolerance | Power |
| 3314J-1-103LF | 10 kΩ | ±20 % | 0.25 W |
| 3314G-1-103LF | 10 kΩ | ±20 % | 0.25 W |
The 3314J-1-102E is a surface-mount single turn trimmer. At 1 kΩ the 210° sweep gives just 4.8 Ω per degree, so small steps stay resolvable. On 3.3 V and 5 V boards it trims outputs and comparator thresholds more finely than the 10 kΩ part.
Body 4.5×4.5×2.55 mm, flat-blade slot 2.45 mm long, 0.51 mm wide and 0.51 mm deep for the H-90 tool. The J-hook terminals bend down and curl back, landing on the pads for reflow. The 102 code and date code are marked on top, one digit apart from the 103.
The wiper crosses the cermet element over 210° against a 240° mechanical angle. The whole 1 kΩ from terminal 1 to 3 sits inside that sweep, so a divider tap at terminal 2 follows the angle. Past either end the wiper idles and over-turning does no harm.
In the part number, 102 is the resistance code: the first two digits 10 are the significant figures and the third digit 2 means × 10², so 1 kΩ; 103 is 10 kΩ. At 1 kΩ, 0.25 W allows only 15.8 V at 15.8 mA. Tolerance ±20 % is ±200 Ω, which is 42° of rotation.
The full datasheet is on page 1 and can be downloaded from this page, with the resistance table, environmental tests, dimensions for the J and G terminals, and tape drawings. Operating range -55 °C to +125 °C, temperature coefficient ±100 ppm/°C. For a packaging code or terminal style, contact our sales team.
√(0.25 W × 1 kΩ) = 15.8 V at 15.8 mA. A 3.3 V board draws 3.3 mA through 1 kΩ for 0.011 W, well inside the rating; a 5 V loop draws 5 mA for 0.025 W, still far from the limit.
Ten times finer than the 47.6 Ω per degree of the 10 kΩ part. The ±20 % tolerance of 200 Ω is 42° of rotation, trimmed back by adjustment; screwdriver repeatability of 2° to 5° moves the setting by 9.5 Ω to 24 Ω.
The E tape for the J and G styles carries 500 pcs, and the 13 inch reel 3000. Check the 102 mark on top at each reel change, since the 103 in the same series looks the same apart from the last digit.