
Bourns 3590S-2-502L ⌀22.2×12.2 mm 10-turn trimmer potentiometer, 5 kΩ, tolerance ±5%, 2 W power rating. For on-board bias, reference and zero calibration.
The 3590S-2-502L is a 10-turn panel-mount wirewound precision potentiometer, body ⌀22.2×12.2 mm, rated 5 kΩ ±5 % with ±0.25 % linearity and 2 W. Metal bushing 3/8-32 UNF, shaft 6.34 mm, solder lug terminals.
| Parameter | Value |
| Series | 3590 |
| Nominal resistance | 5 kΩ |
| Resistance tolerance | ±5 % |
| Power rating | 2 W |
| Turns | 10 turns |
| Linearity | ±0.25 % |
| Temperature coefficient | ±50 ppm/℃ |
| Mechanical rotation | 3600 ° |
| Dimensions | ⌀22.2×12.2 mm |
| Model | Resistance | Tolerance | Power |
| 3590S-2-103L | 10 kΩ | ±5 % | 2 W |
The 3590S-2-502L is a 10-turn panel-mount wirewound potentiometer. At 5 kΩ each turn covers 500 Ω and the 0.025 % resolution works out to 1.25 Ω, finer than the 10 kΩ part. Panel dials, bench supply outputs and test-rack setpoints use it, with every turn counted by hand.
Body ⌀22.2×12.2 mm, metal bushing 9.53 mm across, shaft 6.34 mm, panel hole ⌀9.53 mm for panels 2.46 mm to 3.81 mm thick. Solder lugs at the rear on a 5.08 mm pitch, connected by soldering.
A lead screw carries the wiper through 10 turns, splitting 5 kΩ into 500 Ω per turn. A divider taps the wiper against one end while the 1-2 and 2-3 resistances move in opposite directions. Past either end the wiper idles and nothing jams.
In the part number, 502 is the resistance code: the first two digits 50 are the significant figures and the third digit 2 means × 10², so 5 kΩ; 103 is 10 kΩ. At 5 kΩ, 2 W allows 100 V at 20 mA. Tolerance ±5 % is ±250 Ω, which equals 180° of rotation.
The full datasheet runs from page 1 to page 3 and can be downloaded from this page, with the eight shaft and bushing configurations, the panel cut-out drawing and the recommended part list. Operating range -40 °C to +125 °C, rotational life 1,000,000 shaft revolutions, backlash 1.0° maximum. For shaft length, contact our sales team.
√(2 W × 5 kΩ) = 100 V at 20 mA. Derated to 1.3 W at 70 °C that falls to 80 V at 16 mA; on a 48 V machine the 5 kΩ draws 9.6 mA for 0.46 W, which still leaves margin.
One degree is 1.4 Ω and the 0.025 % resolution is 1.25 Ω, about 0.9° of rotation. The wiper steps one wire at a time, so the output moves in 1.25 Ω steps and nothing finer is available.
±5 % of 5 kΩ is ±250 Ω, which is 180° of the 3600° travel, half a turn. Used as a divider, that 250 Ω shifts the end positions by half a turn, so mark the dial from measured ends rather than from the drawing.