≡ Param Finder by package / current / voltage
TC33X-1-103E 10 kΩ TC33系列微调电位器
上一张
  • TC33X-1-103E 10 kΩ TC33系列微调电位器
下一张

Bourns TC33X-1-103E Trimmer Potentiometer 10 kΩ TC33 Series

Bourns TC33X-1-103E 3.0×3.6 mm single-turn trimmer potentiometer, 10 kΩ, tolerance ±25%, 0.1 W power rating. For on-board bias, reference and zero calibration.

Download

0

The TC33X-1-103E is a 3.0×3.6 mm surface-mount single-turn trimming potentiometer rated 10 kΩ ±25 % with 0.1 W. Top-face adjustment, continuous rotation with no mechanical stop, 8 mm tape. Chosen where a 4 mm part will not fit.

Brand:BOURNS (Joincircuit is an authorised distributor)
Category:Trimmer potentiometer / TC33 系列
Resistance:10 kΩ;Power rating:0.1 W

Specifications

ParameterValue
SeriesTC33
Nominal resistance10 kΩ
Resistance tolerance±25 %
Power rating0.1 W
TurnsSingle turn
Linearity—
Temperature coefficient±250 ppm/℃
Mechanical rotation—
Dimensions3.0×3.6 mm

Other Resistances in This Series

ModelResistanceTolerancePower
TC33X-1-104E100 kΩ±25 %0.1 W

Product Description

What this product is

The TC33X is the smallest surface-mount trimmer Bourns makes, with a 3.0×3.6 mm body, for places a 4 mm part cannot go: headset modules, miniature sensor boards, wearables. Its 0.1 W rating only covers dividers in high-resistance loops, with current in the milliamp range.

Dimensions and appearance

Body 3.0×3.6 mm with the adjustment slot on top for the H-90 tool. The grey area underneath can be dotted with cement so the part stays put through washing and handling. Terminals on both sides, 8 mm tape for pick-and-place.

How it works

The wiper crosses the cermet element over at least 200°. The TC33X-1 is the continuous rotation version, so past either end the wiper idles with no mechanical stop. Terminals 1 and 3 are the element ends and terminal 2 is the wiper, where a divider takes its output.

How to choose

In the part number, 103 is the resistance code: the first two digits 10 are the significant figures and the third digit 3 means × 10³, so 10 kΩ; 104 is 100 kΩ. At 10 kΩ, 0.1 W allows 31.6 V at 3.16 mA. Tolerance ±25 % is ±2.5 kΩ, trimmed back out in a divider.

Parameters and documentation

The full datasheet is on page 1 and can be downloaded from this page, with the resistance table, dimensions and tape drawing. Operating range -40 °C to +100 °C, temperature coefficient ±250 ppm/°C, rotational cycling 20 cycles, and aqueous cleaning is not recommended. For the -1 and -2 versions, contact our sales team.

Selection Notes

1. ±25 % of 10 kΩ lands between 7.5 kΩ and 12.5 kΩ

The ends can sit ±2.5 kΩ away. A divider uses the ratio only, so adjustment brings the output back; used as a two-wire variable resistor the range is 2.5 kΩ short and both end setpoints have to be recalculated.

2. At 10 kΩ the 0.1 W rating allows only 31.6 V

√(0.1 W × 10 kΩ) = 31.6 V at 3.16 mA. On a 5 V board 10 kΩ draws 0.5 mA for 0.0025 W; on a 12 V loop it draws 1.2 mA for 0.014 W, seven times inside the limit.

3. The -1 version rotates continuously with no stop

The TC33X-1 has a continuous mechanical angle, so over-turning leaves the wiper idling and touch cannot find the end. Check the end value with a meter, or take the -2 version with a stop; at either end 200 Ω of end resistance remains, 2 % of full scale.